Main Menu

Improve Your Outcome with Concrete Stencils

unrolling a concrete stencil
The stencil is unrolled and stretched across the slab by two people, one on each side. Photos courtesy of Steve VandeWater

In the early 1980's the first commercially available concrete stencils were introduced. Back then, there was only one pattern: Running Bond Brick. When used on fresh concrete, the disposable paper stencils allowed contractors to easily, quickly and accurately duplicate the look of hand-laid bricks over a large area. The finished product looked just like colored bricks with natural gray mortar between them.

Results were so strikingly authentic that stenciled concrete quickly caught on. Since those early days, many additional stencil patterns have been produced. You can now obtain stencils in brick, cobblestone, flagstone, slate and tile patterns, as well as compasses, rosettes, borders and geometrically shaped accent pieces. There are about 40 patterns in all.

rolling out a concrete stencil
A nylon loop roller is used to get the stencil to stick to the wet surface.

As a contractor, I bought my first roll of stencil in 1994. I had been stamping for a little over a year, and the stencil advertisement in the back of a concrete magazine intrigued me. I liked the idea of getting stamp-like results without ever getting out on the slab. After using the stencils on a small patio, I was immediately hooked. I found stenciling was so much simpler than stamping that I could produce great looking work more quickly and would be able to tackle much larger areas at a time.

A great alternative to stamping
The reason stenciling is so much quicker is that all work can be done from outside the forms using long-handled tools. The pattern is provided by the stencils, and texturing may be accomplished with lightweight textured rollers. Unlike stamping, there’s no need to get out on the slab, waiting until it can bear your weight and then hurrying to stamp every square inch by hand.

As any stamper can attest, the window of opportunity is often very short. Concrete sometimes sets too quickly to be adequately textured. This situation can be alleviated with stencils. The stenciling process can begin as soon as the concrete is bull floated and can sometimes be completed before the concrete even reaches the stage where stamping could begin. I’ve gone home from finished stencil jobs while the concrete was still incredibly soft.

applying dry shake color over a concrete stencil
One of the crew applies dry shake color hardener after the stencil is securely in place.

Because stenciling is quicker, it’s ideal for large areas. Larger pours eliminate the need for cold joints or construction joints between slabs, and this in turn eliminates potential color differences between those two separately poured slabs. Driveways, especially those on a moderate to steep incline, are ideal for stencils. An entire driveway can easily be done in one pour, whereas if stamped, it might take several pours. When stamping on an incline, stamps will sometimes creep downhill as they are being tamped, creating misalignments, drag marks and ugly joints. Stenciling eliminates these problems.

Since my first stencil job in ’94, my company’s work was split about 50:50 between stamping and stenciling. So why didn’t I use stencils all the time?

concrete texture roller
Texture is applied with a roller over Powdered release. Although you can barely; see it, a stencil is in place.

Potential problems with stencils
Although stencils are often much simpler and quicker, stamps are a better option at times. These instances include when pouring slabs that are not easily accessible from two opposite sides (such as a patio poured back in a corner), on breezy days, or when using patterns such as Ashlar Slate or Herringbone Brick.

To easily place stencils, two people must be able to stand outside the forms on opposite sides of the slab. From this position, they lay the stencil onto the concrete surface. In a corner though, this is impossible to do. One person is going to be standing in the concrete. This situation can be eliminated by talking the homeowner into incorporating a planting bed between the wall and the slab. Aesthetically, it looks better, and it gives the second person a place to stand while placing the stencil.

Windy days wreak havoc on stencil placement. The wind blows the stencil around, making it very difficult to line up. In addition, wind often dries the surface prematurely and makes it difficult to stick the stencils to what would otherwise be wet concrete.

Some patterns simply look better stamped than stenciled. Ashlar Slate stencils exhibit “stones” which are much smaller than typical real pieces of slate, so the finished work doesn’t look as realistic as stamped Ashlar Slate. One stencil pattern in particular — Herringbone Brick — is just plain difficult to use. Because of the way the stencil is cut, it is a nightmare to use on areas wider than 8 feet. A walk board bridging the pour is often required to place this pattern. In most cases, though, stencils are a great alternative to stamps.

remove concrete stencil
It’s imperative to remove the stencil immediately after texturing.

Economy and ease of training workers

The stenciling process is so simple that it can be done by almost any competent finisher his or her first time out. Stamping, on the other hand, has a much longer learning curve.

Stencils make it easier for contractors to train new workers. Plus, since the disposable stencils are single-use items, stenciling contractors can offer their customers more than 40 patterns, with the cost of the chosen stencil paid in-full with each job. With expensive stamp mats, it may require contractors to sell several jobs of the same pattern to recoup their investment. What if they buy a set of stamps and the next customer doesn’t like that pattern?

The stenciling process in a nutshell

Here are the basic steps in a stencil application:

stenciled concrete driveway
The job is complete.
  • The concrete is poured, screeded, bull floated and edged as normal. Stenciling can begin immediately thereafter.
  • The stencil is unrolled and stretched across the slab by two people on opposite sides. It is cut from the roll with scissors. The stencil is laid atop the slab and plastered to the wet surface with a special roller, making sure it’s securely stuck down so that no color can get beneath it. The process is repeated, overlapping the previous piece of stencil by one “mortar joint.” Continue until the slab is covered.
  • When all the stencil sections are placed and stuck down, dry shake color hardener is applied and floated into the surface. The stencil masks the color from the “mortar joints” so they will remain gray. Do not work the stencil into the concrete or it will be embedded too deeply and cause problems. The stencil should remain on the surface, not under it.
  • Release agent (either clear liquid or antiquing powder release) is applied to the surface.
  • A textured roller is passed over the slab. It is helpful to do this in random directions to minimize obvious repetition of texture.
  • As soon as texturing is complete, the stencil is removed by two people on opposing sides of the slab, starting with the last piece of stencil placed. The stencil is lifted straight up so as not to drag it, and is carried off the end of the slab and discarded. Repeat until the entire stencil is removed.
  • Removing the stencil while the concrete is still soft will result in sandier, more natural-looking joints. Leaving it in longer will yield slick, plastic-looking ones. Under no circumstances should you wait until the next day to remove the stencil.

The following day, saw-cut the crack-control joints, and wash off the dust and excess release agent. When dry, seal the slab.

That’s it. Decorative concrete can’t get much easier than stenciling!

Steve VandeWater, a former decorative concrete contractor, is the creator of the Indiana Decorative Concrete Network website He currently manages The Concrete Store at Sagamore Ready Mix in Fishers, Indiana.

Related Content

World of Concrete 2018 Annual Rite of Winter was Ripe with Innovation

Brickform stamp shown at 2018 World of Concrete.World of Concrete 2018 exceeded everyone’s expectations in January by attracting more than 58,000 registered professionals and nearly 1,600 participating companies, including about 300 brand-new exhibitors.

A Variety of Tools and Techniques Adds Texture to Concrete Slabs

Texture roller skims the surface of a stenciled concrete slab giving a textured look.In this world, there are two types of concrete: concrete that’s flat, gray and utilitarian, and concrete that’s been shaped, colored and/or textured — and is considered art.

Creating Color Designs with FloorMaps' Stencils

A stencil in the shape of puzzle pieces was applied to this concrete floor and takes on a 3-D look.Complex and intricate designs can be applied to concrete surfaces very accurately using adhesive-backed vinyl stencils. They offer control, precision and, if needed, repeatability. Stenciling is a very old technique from the world of paint, but as it evolves in the concrete world, it’s becoming very modern.

Using Stencils to Expand Artistry in Decorative Concrete

Applying a stencil to a floor creating an artistic look when artistic talent is lacking.Because their artistry is computer-generated, stencils empower every contractor to create stunning works of art regardless of artistic talent. It is amazingly simple to produce logos, images, and artistic effects with exact detail and concrete industry has an arsenal of magnificent images ready to order.