Main Menu

Applying Concrete Densifiers -- Feel Good About Rejection

One message comes through loud and clear in any discussion, debate or disagreement about the various types of densifiers used in concrete polishing.

Almost all of them work. (With one exception — read on.)

Beyond that point of essentially universal agreement, the discussion takes on a different spin, addressing the sometimes subtle attributes and pitfalls of using sodium, potassium or lithium silicates or the newer kid on the block, colloidal silica.

Then, with increasing emphasis, follows a second message: It’s about rejection.

While personal rejection can take a toll on one’s self-esteem, densifier makers and polished concrete contractors voice agreement that a concrete surface’s rejection of additional densifier signals that the concrete has gotten the dose of treatment it needs to succeed in its mission of durability and visual enhancement.

“We tell contractors to densify until rejection,” says Brad Burns, executive director of the Concrete Polishing Association of America. “That way you have the best wear resistance possible for concrete.”

The characteristics and composition of densifiers, how best to use them, and a number of other key concrete polishing issues are addressed in a series of position papers and definitions developed by the CPAA.

The definitions, which can be found in the “Glossary” section of the CPAA website, include this entry on liquid densifiers:

“An aqueous solution of SiO2 (silicon dioxide, or silica) dissolved in the respective Hydroxide that penetrates into the concrete surface and reacts with the Calcium Hydroxide to provide a permanent chemical reaction that hardens and densifies the wear surface of the cementitious portion of the concrete.”

The definition lists four types: sodium silicate, potassium silicate, lithium silicate, and an “alkalis solution of colloidal silica or silicates.”

The definition for densifiers is designed “to help architects understand that all densifiers harden the concrete,” Burns says. “That being said, they’re not all the same. One may perform quicker or better than another. That’s where contractors learn to use different brands. It’s not necessarily the chemistry, it’s the formula.”

Burns also notes that colloidal silica suspended only in water would be nonreactive. That’s his exception to the idea that “they all work.”

Different types, different practices

So what about these various types of densifier? Let’s look at what seasoned experts say with regard to how they work in practice, and about how to ensure the densifier does the job of densifying most effectively.

“They all perform the same way,” Burns says. “Regardless of what you use as a carrier, the silicate does the work.

“With sodium, you put down a lot of liquid, scrub, and clean the surface. If you are going to apply it early in the process, there’s no need to worry about getting it off the surface because it will be ground off.”

In marketing spin, lithium is advertised as easier to apply. Nevertheless, Burns cautions that “in the real world,” the same rules apply: If the concrete surface is porous, more densifier is required. “It’s about application at the job site and determining what the variables are,” he says.

“With lithium, the manufacturers advise use of less material, so you must make sure you are getting plenty of densifier in the concrete.”

Potassium silicate hardeners are applied in a similar fashion to sodium silicates — flooding the surface, essentially, and scrubbing the solution into the concrete — while colloidal silicas are used more like lithium silicates, with a sprayer and a microfiber applicator.

The CPAA gets no argument from manufacturers on the matter of application to the point of rejection.

“To comply with the ATSM method of application you need to flood the floor with the silicate for a minimum of 30 minutes or until it will not accept any more material,” says Scott Thome, director of product services for L. M. Scofield Co. Scofield offers a trio of densifier chemistries — sodium, potassium and lithium.

The square-foot coverage rate of a silicate is between 400-500 square feet per gallon on a normal concrete substrate. Applying them at 800-1,000 square feet per gallon “is just not enough,” Thome says. By the time the contractor puts two to three sets of diamonds on the floor after applying the silicate, it could easily be removed. The floor will then perform as if no silicate had ever been applied.

Thome also offers the following recommendations and suggestions:

  • When lithium silicate is applied to the floor and allowed to dry, it develops a film on the surface resembling crushed glass and can be difficult to remove. This material is the silicate component in a dry phase. When the residual silicate is allowed to dry and there are no signs of film development, a question arises as to what the actual solids content of that particular material is. A suggestion is to test and use each material to determine which one works best.
  • Sodium silicates are well suited for large warehouse applications that are not “architectural.”
  • Potassium silicates are recommended for architectural floors that are gray or integrally colored and are to be chemically polished.

Lithium silicate is considered a “default” densifier by Scofield and regarded as easy to apply, as minimal agitation is needed for penetration. Once the floor has been saturated and will not absorb more material, the excess should be removed unless metal bond diamonds will be used after the silicate has been placed.

Optimum application amounts

Mark Vogel, director of international sales for W.R. Meadows Inc., says manufacturers are moving away from the “ease of application” pitch toward emphasizing the need to saturate the surface to get proper densification. “It’s simple and it’s true,” he says.

“When lithium first came out, the manufacturers said just mist it, wipe it and are you good to go. That’s nowhere near what’s needed,” he says. “It was said it could do 1,000 square feet per gallon. This resulted in soft areas and premature erosion.”

Densifying to rejection, in contrast, addresses variations in hardness typical in any concrete slab, he notes.

Unlike “drowning the surface” with sodium silicates, the recommendation for lithium silicates is to aim for an optimum application amount with the sprayer and microfiber mop.

“The key is knowing and understanding concrete and watching. The first 10 minutes are the most crucial, when you see if the concrete is absorbent or not absorbent. Then you either add more or, if it’s not absorbed, you wait a little longer to see if it does absorb. If there still is a sufficient amount on the surface, you don’t do anything.

“The key is the applicator judging absorbance and how much to get into the concrete.”

Joe Reardon of Prosoco Inc., a maker of lithium silicate densifiers, agrees that the contractor must “read the floor and how much it’s going to take”: maybe at a high rate of 300 square feet per gallon if it’s soft, two coats if it’s “really soft.”

But Reardon, concrete products group specialist for Prosoco, adds that oversaturation with lithium silicates can cause “whitening out” of the surface — deposition of a layer of excess silicate that is difficult to remove due to lithium’s insolubility in water.

“It really comes down to the applicator knowing the situation with the floor. We rely on them to read that floor,” he says.

Colloidal silica densifiers are the claim to fame for Lythic Solutions Inc. Its president, David Loe, says ultra-low levels of metallic salts in colloidal-silica densifiers prevents the whitening problem, while the products’ low pH addresses the matter of worker safety and hazardous-materials disposal. Other favorable characteristics, he says, are low viscosity and rapid rates of penetration and reaction with concrete.

To get optimal results with any densifier, Loe offers the following recommendations:

  • Make sure the surface is not contaminated by oils or other substances that may prevent densifier penetration.
  • Test densifier performance on the particular concrete being treated. All slabs are different, different pours on the same slab are different, and concrete placed on different substrates (on grade versus on deck) from the same pour can be different.
  • Follow the manufacturer’s directions carefully. This is crucial with silicates, where the margin for error can be small if whiting is to be avoided. Overapplication of silicates can cause whiting, but underapplication will mean lack of densification.
  • Call the manufacturer immediately with any questions or problems.

Related Content

How to Avoid Pitfalls When Polishing Concrete Floors in Retail Facilities

How to avoid pitfalls when polishing concrete floors in retail facilitiesAccording to the news, retail brick-and-mortar facilities are declining at a rapid rate. While I agree 100 percent that internet sales are impacting sales at traditional stores, this market segment is still relevant. And when it comes to polished concrete at retail establishments, business is still booming.

Decorative Concrete Award Winners Elevate Industry Expectations

decorative concrete award winnerPassion, precision, artistry and creativity were all on display at the L. M. Scofield Co. ninth annual Decorative Concrete Awards ceremony. Scofield enlists professionals from the concrete industry to judge submissions based on skill of installation, artistic expression and integration with the overall design intent.

Sprawling Aged Concrete Meets its Endurable Match

Concrete floor restoration in Nebraska's Timpte Manufacturing Plant filled in gouges, holes and cracks in the concrete.It wasn’t long after Shawn MacDonald heard about a promising new concrete floor restoration system that he encountered a project that figured to be a good candidate for putting the system to the test.